P0388 Engine Trouble Code

When you check engine light came on code P0388 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the P0388 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

P0388 code can be about changing a broken oxygen sensor can lead to a busted catalytic convertor which can cost upwards of $1,300. Taking your vehicle into a service shop will cost you around $300 depending on the vehicle. But, an oxygen sensor is easy to replace on many vehicles and is detailed in the owner's manual PDF or in our website. If you know where this sensor is located, you only have to unclip the old oxygen sensor and replace it with a new sensor. Regardless of how you approach it, you should get this fixed right away.

P0388 Code Meaning :

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P0388 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P0388 OBD-II Trouble Code The Crankshaft position sensor also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. This information is used by the P0388 code. Fuel Rail Pressure Sensor Circuit Malfunction and Cylinder 1 Injector Circuit Low causes most of code P0388.

Reason For P0388 Code

The reason of P0388 OBD-II Engine Trouble Code is Fuel Rail Pressure Sensor Circuit Malfunction.

Your car parts or components should not be replaced with reference to only a P0388 DTC. The vehicle service manual should be consulted for more information on possible causes of the error code, along with required testing.

How To Repair P0388 Code

Before starting let's see P0388 repairing process steps:

• Qualified technicians will begin by using a scan tool to access P0388 code stored in the ECU.
• Technicians will note P0388 code present and any freeze frame data associated with them.
• After all, if you sure the engine trouble is finished, the code will be cleared.

A bad fuel pressure regulator can result in an accumulation of too much gasoline/diesel that causes your engine to backfire or the fuel to smell when you slow down your vehicle. If you see even a slight problem, it is essential to have it inspected to quickly correct any issues before any damage is further imposed on your car.

A digital volt/ohmmeter may be necessary to compare the voltage reading with the manufacturer's specifications. The mechanic should always clear the code and retest the system after each possible repair, to ensure that they've made the proper diagnosis.

Sometimes P0388 code comes with P038800 code.

Diagnosis Of Engine Error OBD Code P0388

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P0388 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P0388 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.